mso-hansi-font-family:"Times New Roman"">一、概述:
mso-hansi-font-family:"Times New Roman"">依据GB/T16777-1997 "Times New Roman"">标准设计制造的本涂膜模具是建筑防水材料(聚氨酯类、聚丙烯酸酯类)拉伸性能系列试验,制备试样用的涂膜模具。用此涂膜模具能制出350mm mso-hansi-font-family:"Times New Roman"">×320mm "Times New Roman"">×1.5mm的试样膜,然后用切片机切割涂膜可制得符合GB/T528标准规定的哑铃状Ⅰ型试样,以备不同拉伸试验之用。
mso-hansi-font-family:"Times New Roman"">二、涂膜模框结构及尺寸规格:
1、结构:本涂膜模具由模框、涂刮棒、基板及底座组成(见附图)
2、尺寸规格:
mso-hansi-font-family:"Times New Roman"">外框尺寸410mm "Times New Roman"">×380mm×1.5mm
mso-hansi-font-family:"Times New Roman"">内框尺寸350mm "Times New Roman"">×320mm×1.5mm
mso-hansi-font-family:"Times New Roman"">涂膜厚度(1.5 "Times New Roman"">±0.2)mm
mso-hansi-font-family:"Times New Roman"">三、涂膜模框操作方法:
1、在试样制备前,所取样品及所用仪器均在标准条件下(温度23 mso-hansi-font-family:"Times New Roman"">℃±2 "Times New Roman"">℃;相对湿度45 "Times New Roman"">%~70%) "Times New Roman"">放置24h。
2、为了便于脱模,在基板(玻璃板)上和模框上可用硅油或石蜡作脱模剂进行表面处理。
3、在标准条件下,将静置后的样品搅拌均匀,若样品是双组分涂料,则按产品的配合比称取所需的主剂和固化剂,把两组分混合后充分搅拌5min mso-hansi-font-family:"Times New Roman"">。
4、在不混入气泡的情况下将搅拌好的防水涂料立即倾倒于本涂膜模具中进行涂覆。
5、样品应分次涂覆,最后一次用涂刮棒将其表面刮平,并在标准条件下养护168h mso-hansi-font-family:"Times New Roman"">。
6、检查涂膜外观,表面应无明显气泡、光滑且平整。
7、起膜后,用切片机切割涂膜,制得符合GB/T 528所规定的哑铃状Ⅰ型试样,一备不同拉伸试验之用。
mso-hansi-font-family:"Times New Roman"">四、涂膜模框注意事项:
1、切割试样时应注意试样边缘与涂膜边缘之间的距离不得小于10mm mso-hansi-font-family:"Times New Roman"">,两试样之间的距离也不得小于10mm "Times New Roman"">。
2、由于涂刮棒相对较长且直径较小,在使用完毕清洗干净后,应悬挂垂直放置,以防变形。
3、模框使用时应是长边在上,即长边压短边。
mso-hansi-font-family:"Times New Roman"">五、涂膜模框装箱单:
1、涂膜模具1 mso-hansi-font-family:"Times New Roman"">个(模框)
2、使用说明书1 mso-hansi-font-family:"Times New Roman"">本
3、合格证1 mso-hansi-font-family:"Times New Roman"">张
4、涂刮刮板部件1 mso-hansi-font-family:"Times New Roman"">件