mso-hansi-font-family:"Times New Roman"">高温/ "Times New Roman"">低温沥青软化点试验仪 智能沥青软化点试验器 "Times New Roman"">软化点配件
mso-hansi-font-family:"Times New Roman"">一、产品简介:
mso-hansi-font-family:"Times New Roman"">沥青软化点仪是根据GB/T4507 "Times New Roman"">、ASTMD36 "Times New Roman"">、T0606-2000 "Times New Roman"">沥青软化点测定法( "Times New Roman"">环球发)的规定制造,用于测定沥青在规定的条件下软化且下坠达25mm mso-hansi-font-family:"Times New Roman"">时的温度。符合交通部JTJ052-2000 "Times New Roman"">标准。
mso-hansi-font-family:"Times New Roman"">二、沥青软化点测定仪主要特点:
1、温度由仪器自控,无人为误差
2、外置式温度探头,对温度反映灵敏
3、速度采用PID mso-hansi-font-family:"Times New Roman"">加模糊逻辑算法控制,线性升温
4、新型外观,操作更加方便
5、有磁力搅拌装置,试验温度更均匀
6、自动、手动两种记录试验结果,自动计算平均值
mso-hansi-font-family:"Times New Roman"">三、主要技术指标:
1、测温范围:-5 mso-hansi-font-family:"Times New Roman"">-125℃
2、试验范围:5 mso-hansi-font-family:"Times New Roman"">-90℃
3、升温速率:(5±0.5) ℃/min
4、升温方式:升温速度采用PID mso-hansi-font-family:"Times New Roman"">加模糊逻辑算法控制,磁力搅拌
5、检测方式:自动、手动检测
6、钢球质量:3.5g±0.05g
7、钢球直径:9.53mm
8、钢球下沉:25.4mm
9、环:JTJ052 mso-hansi-font-family:"Times New Roman"">-2000 "Times New Roman"">规程标准
10、计时范围:0 mso-hansi-font-family:"Times New Roman"">-99 "Times New Roman"">分99秒
11、测温精度:0.1℃
12、执行标准:GB/T4505、ASTMD36、T0606-2000
13、外形尺寸:300×200×300mm
14、重量:12KG
15、电源电压:220V
16、功率:1KW
17、环境温度:5 mso-hansi-font-family:"Times New Roman"">~40℃
18、环境湿度:≦85%
mso-hansi-font-family:"Times New Roman"">四、沥青软化点测定仪使用说明:
mso-hansi-font-family:"Times New Roman"">将试样放在规定尺寸的金属环内,上置规定尺寸和重量的钢球,放于水( mso-hansi-font-family:"Times New Roman"">或甘油) "Times New Roman"">中,以5±0.5℃/min "Times New Roman"">的速度加热,至钢球下沉达到25.4mm "Times New Roman"">时,记下该时温度即为该试样软化点。
mso-hansi-font-family:"Times New Roman"">五、操作规程:
1、在烧杯中放入800 mso-hansi-font-family:"Times New Roman"">~1000ml "Times New Roman"">蒸馏水,在室内温度较低时可放少一些,在室内温度较高时可放多一些。
2、通过加热或放入冰水中,使烧杯内的温度调节到5℃ "Times New Roman"">。
3、把磁力搅拌子放至烧杯底部中间的位置。
4、将两个试样放入试样环中,并把两个钢球放到试样的中央。把试样放入烧杯中恒温不少于15min mso-hansi-font-family:"Times New Roman"">。
5、把烧杯置于试验器中,插上电源插座。
6、打开电源开关,按下“ mso-hansi-font-family:"Times New Roman"">启动” "Times New Roman"">按钮,通过调节调速按钮,使搅拌子的转速调到合适的位置。开始加热时,搅拌子的转速可快一些,当水温接近软化点时,停止转动。
7、当试样下降到25.4mm mso-hansi-font-family:"Times New Roman"">处时,试验器发声,表示试验结束。
8、按“ mso-hansi-font-family:"Times New Roman"">结果” "Times New Roman"">按钮,在温度显示器上读取平均温度。
mso-hansi-font-family:"Times New Roman"">注意:在测试过程中严禁按“ "Times New Roman"">复位”键。
mso-hansi-font-family:"Times New Roman"">六、沥青软化点测定仪校验方法:
1、用外径千分尺测沥青软化点仪钢球相互垂直的三个直径, mso-hansi-font-family:"Times New Roman"">再用分析天平称其重量。
2、检查沥青软化点仪钢球和试样环表面是否生锈或残缺。
3、及外径千分尺测量试样环图示各部位的尺寸。
4、用游标卡尺测量沥青软化点仪支架承环下缘与承板的距离。
5、用钢直尺测量沥青软化点仪耐热热玻璃烧杯尺寸。
mso-hansi-font-family:"Times New Roman"">七、注意事项:
1、仪器使用与存放必须小心轻放,以免损坏玻璃制品及温度计
2、每次试验完毕,必须将仪器擦拭干净。