HDMI网线30米延长器 由HDMI输入经过盒子的内部调节再通过网线传输30米给接收端，有接收端输出HDMI信号给显示器。 HDMI Extender over 2 UTP Cables with IR Control HDV-E50D(50m/164ft) HDV-E30D(30m/100ft) User manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. I. Introduction The HDMI extender over 2 UTP cables with IR control is the right way to send your HDMI signal over long distances. Instead of using expensive HDMI cables, this device lets you use your existing Cat5e/ 6 cables/sockets while also performing the same functions like transferring Deep Color (12 bits/color) video and new lossless compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio) digital audio, all with a bandwidth up to 225MHz. And if that weren’t enough, you can use your existing remote to control your device through an IR blaster. II. Features Compliant with HDMI 1.3, HDCP 1.1 and DVI1.0 standards. Supports digital video formats in Deep Color Mode at up to 36 bits (12bits/color) and new lossless compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio) Digital audio . Supports Cat5e/6 cables for data/DDC transmission. Equalizes and recovers incoming TMDS data before re-transmitting it in high quality, regardless of the incoming signal quality. Supports CEC bypass and xvYCC. Supports HDMI1.4 with 3D and ARC fuction. Super IR control system, IR transport channel can be forward or backward. III. Package HDMI Transmitter HDMI Receiver IR Tx cable IR Rx cable 5V1A DC Power Supply Adaptor Product Manual IV. Specifications HDMI Transmitter ports 1 x HDMI,1x IR Tx, 2xCat5e/6 HDMI Receiver ports 1 x HDMI,1x IR Rx, 2xCat5e/6 Power Supply 1x 5V1A DC ESD Protection Human body model 8kV (air-gap discharge) , 4kV (contact discharge) Dimension 80mm x 41mm x 25 mm Weight 150g Operating Temperature 0 C ~ 40 C / 32 F ~ 104 F Storage Temperature -20 C ~ 60 C / -4 F ~ 140 F elative Humidity 20 ~ 90% RH (Non-condensing) V. Connect and Operate Connect the signal source such as Blu-Ray Player, Play Station 3, audio/video receiver, cable or satellite receivers and computers equipped with HDMI output interfaces with a short high-speed HDMI cable to the HDMI Transmitter input. HDMI cable length should not exceed 16 ft. Connect the HDMI Transmitter output RJ-45 ports using dual-runs of Cat 5e or Cat 6 UTP cables to included Receiver, which does not require a power supply. It is strongly recommended that factory terminated cable assemblies be used and their length shall not exceed 100 ft of Cat 5e and 110 ft of Cat 6 for the 30 m extenders and 164 ft and 180 ft respectively for the 50 m extenders. Connect the HDMI output from the Receiver to high-definition display devices such as HD-LCD, HD-DLP and HD projectors with HDMI input interfaces. Use high-speed HDMI cables that are recommended for the distances that are required for each connection. HDMI cable length should not exceed 16 ft. The Receivers are powered by an external power supply which is included. Connect power first to the source, then to the Receiver and then to each HD TV or projector. The source can be controlled from the display. This is accomplished by using an optional IR Receiver pigtail pointing away from the display, which can be connected to the receiver portion of the extender. The IR Transmitter pigtail is then connected to the Transmitter of the extender and pointed at the source.